收藏本站
LT3475/LT3475-1
APPLICATIONS INFORMATION
with the energy stored in the inductor, the circuit will rely
on some minimum load current to get the boost circuit
running properly. This minimum load will depend on input
and output voltages, and on the arrangement of the boost
circuit. The minimum load current generally goes to zero
once the circuit has started. The typical performance char-
acteristics section shows a plot of minimum load to start
and to run as a function of input voltage. Even without an
output load current, in many cases the discharged output
capacitor will present a load to the switcher that will allow
it to start. The plots show the worst case, where V IN is
ramping very slowly.
Programming LED Current
The LED current can be set by adjusting the voltage on the
V ADJ pin. For a 1.5A LED current, either tie V ADJ to REF or
to a 1.25V source. For lower output currents, program the
V ADJ using the following formula: I LED = 1.5A ? V ADJ /1.25V.
Voltages less than 1.25V can be generated with a voltage
divider from the REF pin, as shown in Figure 6. In order
to have accurate LED current, precision resistors are
preferred (1% or better is recommended). Note that the
V ADJ pin sources a small amount of bias current, so use
the following formula to choose resistors:
the voltage on the V ADJ pin by tying a low on resistance
FET to the resistor divider string. This allows the se-
lection of two different LED currents. For reliable op-
eration program an LED current of no less than 50mA.
The maximum current dimming ratio (I RATIO ) can be
calculated from the maximum LED current (I MAX ) and the
minimum LED current (I MIN ) as follows:
I MAX /I MIN = I RATIO
Another dimming control circuit (Figure 8) uses the PWM
pin and an external NFET tied to the cathode of the LED.
An external PWM signal is applied to the PWM pin and the
gate of the NFET (For PWM dimming ratios of 20 to 1 or
less, the NFET can be omitted). The average LED current is
proportional to the duty cycle of the PWM signal. When the
PWM signal goes low, the NFET turns off, turning off the
LED and leaving the output capacitor charged. The PWM
pin is pulled low as well, which disconnects the V C pin,
storing the voltage in the capacitor tied there. Use the C-RC
string shown in Figure 8 and Figure 9 tied to the V C pin for
proper operation during startup. When the PWM pin goes
high again, the LED current returns rapidly to its previous
on state since the compensation and output capacitors are
at the correct voltage. This fast settling time allows the
R2 =
V ADJ
1.25V – V ADJ
R1
+ 50nA
R1
REF
LT3475
To minimize the error from variations in V ADJ pin current,
use resistors with a parallel resistance of less than 4k. Use
R2
V ADJ
GND
3475 F07
resistor strings with a high enough series resistance so as not
to exceed the 500μA current compliance of the REF pin.
Dimming Control
There are several different types of dimming control
DIM
Figure 7. Dimming with a MOSFET and Resistor Divider
circuits. One dimming control circuit (Figure 7) changes
PWM
100Hz TO
PWM
V C
REF
10kHz
LT3475
3.3nF
10k
R1
LT3475
LED
GND
0.1μF
V ADJ
3475 F08
R2
GND
3475 F06
Figure 6. Setting V ADJ with a Resistor Divider
Figure 8. Dimming Using PWM Signal
3475fb
14
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LT3476EUHF#PBF IC LED DRVR HP CONST CURR 38-QFN
LT3477EFE#PBF IC LED DRVR HP CONS CURR 20TSSOP
LT3478IFE#PBF IC LED DRVR HP CONS CURR 16TSSOP
LT3486EFE#PBF IC LED DRVR WHITE BCKLGT 16TSSOP
LT3491EDC#TRMPBF IC LED DRIVER WHITE BCKLGT 6-DFN
LT3492IFE#TRPBF IC LED DVR HP CONST CURR 28TSSOP
LT3496IUFD#PBF IC LED DRVR WHT/RGB BCKLT 28-QFN
LT3497EDDB#TRMPBF IC LED DRIVR WHITE BCKLGT 10-DFN
相关代理商/技术参数
LT3475EFE-1#PBF 制造商:Linear Technology 功能描述:LED DRIVER BUCK PWM 600KHZ 制造商:Linear Technology 功能描述:LED DRIVER, BUCK, PWM, 600KHZ, TSSOP-20
LT3475EFE-1#TRPBF 功能描述:IC LED DRVR HP CONS CURR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND
LT3475EFE-1-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Step-Down l 1.5A LED Driver
LT3475EFE-1-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Step-Down l 1.5A LED Driver
LT3475EFEPBF 制造商:Linear Technology 功能描述:Dual Step-Down 1.5A LED Driver,LT3475
LT3475EFE-PBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Step-Down l 1.5A LED Driver
LT3475EFE-TRPBF 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Step-Down l 1.5A LED Driver
LT3475FE-1 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Step-Down l 1.5A LED Driver